Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
How To Cure High Idle Issues (possibly)
Author Message
peterbaron Online
1st Service Completed

Brampton, ON, Canada, '13 CB1100A
Posts: 89
Joined: Jan 2016
Post: #51
RE: How To Cure High Idle Issues (possibly)
(11-22-2017 08:37 AM)pdedse Wrote:  
(11-22-2017 04:51 AM)peterbaron Wrote:  Not my intention to provide complicated diagnosis, but step by step as a general rule for all TPS as indicated

And it's greatly appreciated!

(11-22-2017 04:51 AM)peterbaron Wrote:  ...never stated " have to open up TPS?????" = sealed unit/do not overhaul...

Not my intention to put words into anyone's mouth, my bad. I didn't have a clear understanding of what jdvalero actually did for his fix, so I was wondering/assuming that the "innerds" there somewhere had been tinkered with...which is where I would have stopped.

(11-22-2017 04:51 AM)peterbaron Wrote:  For all fellows who have skills in different fields - not automotive, I would suggest as follow::
ignition off, disconnect 3 prong TPS connector , inspect, clean it, reconnect...may help if TPS connection was poor, contaminated.... anybody , who rides a motorcycle can do it.

This is what I was looking to confirm! : ) Thanks. I think even with my often limited mechanical skills I can be included with as part of "anybody who rides".

Thanks again,Thumbs Up

NO PROBLEM... thank you for your feedback and notes..
have trouble free riding
Biker

pb
11-22-2017 08:40 AM
Find all posts by this user Quote this message in a reply
jdvalero Offline
1st Service Completed

Raleigh
Posts: 146
Joined: Sep 2016
Post: #52
RE: How To Cure High Idle Issues (possibly)
(11-21-2017 02:12 PM)popgun Wrote:  Until JD responds, I will tell you that is the TPS sensor. DO NOT try to adjust it any unless you have a good understanding of how they work and the min/max voltages. There is NO procedure for it in the service manual.
Yes !!! I agree with popgun on trying to adjust it. Just don't!
That connector that goes into (female) is where the problem was. The hole in which the pin from the sensor goes in is what was twisted and came out easily from the connector. That's why when I did that hard run on the Hwy it must of come out of contact.
See the pic below and me pointing with mechanical pencil. The one wire that was giving me the problem was if not mistaken the black one. İmage
(This post was last modified: Yesterday 01:41 AM by jdvalero.)
Yesterday 01:12 AM
Find all posts by this user Quote this message in a reply
pdedse Offline
Running Like a Top

Oregon
Posts: 434
Joined: Dec 2013
Post: #53
RE: How To Cure High Idle Issues (possibly)
Thanks jdvalero for photo and explanation. I may have implied in a post that others had "opened up" or adjusted the TPS when I wasn't really sure what had been done, so there was never going to be any "adjustment" on my part.

But if your fix involving that wire / connector holds and the problem doesn't come back, that's huge. Because 30+ riders on this forum have bikes with very similar, if not exact symptoms. Previous "fixes" tried by many of us, have not panned out, maybe working briefly. Maybe we're getting closer to finding "the culprit", a weak-link in the system so to speak.
Yesterday 07:48 AM
Find all posts by this user Quote this message in a reply
peterbaron Online
1st Service Completed

Brampton, ON, Canada, '13 CB1100A
Posts: 89
Joined: Jan 2016
Post: #54
RE: How To Cure High Idle Issues (possibly)
(11-21-2017 08:41 PM)Cormanus Wrote:  Ferret, +1.

Peterbaron, you’ve set out remarkably clearly why it would be a huge mistake for me to fiddle with the TPS. Thank you.

Everybody has skills in different fieldsThumbs Up...is my natural advantage that I have in automotive...actually TPS is very simple = only 3 wires..supply voltage (usually 5V), ground and signal...do not want to go Hi Tech..'cuz some members get upset and have stomach irritation, to cure it = Beer...LOL...
You can always go simple way in this matter::
ignition off, disconnect TPS connector, inspect both sides (female and male pins)... and if OK, clean it, apply conductive enhancement, reconnect, test it.... but this is "a ready" answer, without understanding what is going on..SadHuh
The issue is:: catch erratic idling when engine is at operating temperature by wiggling TPS connector...and THEN go step by step as indicated above or in thread = diagnosis first = fix it right at the first time...don't let strangers dig into you bike...LOL
Trouble free riding in beautiful AustraliaBiker

pb
(This post was last modified: Yesterday 08:09 AM by peterbaron.)
Yesterday 08:08 AM
Find all posts by this user Quote this message in a reply
Post Reply 


[-]
Recent Posts
Room for One More?
Here is the Chip Beck mod: popgun — 02:31 AM
New Mirrors and Rear Rack from samurider
Good night dlx's are beautiful. The 4 pi . . .The ferret — 08:00 PM
Room for One More?
Look up " Chip Beck lic plate mod" in t . . .kennyw — 07:46 PM
Room for One More?
:hello: and howdy to the forum. We'll ma . . .The ferret — 06:23 PM
Turkey Day spin
Riding on Thankgiving is a blessing. Gla . . .The ferret — 06:17 PM
Room for One More?
No disrespect assumed, Chunk. My persona . . .Cormanus — 06:04 PM
Room for One More?
Thanks for the welcome! And I very much . . .Chunk — 06:01 PM
New Mirrors and Rear Rack from samurider
Lookin good!greekcb — 05:48 PM
New Mirrors and Rear Rack from samurider
Looks beautiful !!!Houtman — 05:43 PM
Room for One More?
Welcome Chuck!popgun — 04:39 PM

[-]
Statistics
» Members: 3,893
» Latest member: Cory
» Forum threads: 9,974
» Forum posts: 178,844

Full Statistics

>
Forum Jump: